Our Services

FFL Transfer Service

$25 Per.

Labor Rates

Repair service — $50 per hour

Customization and fabrication — $75 per hour

General

Complete detailed cleaning — $50-$125

This includes pulling the entire firearm apart and cleaning everything from the trigger assembly to the bolt, firing pin or striker assemblies and the gas system if applicable. Applying lubricant where it is needed and ensuring all fasteners are at the correct torque spec when reassembled. 

Barrel stripping — $75-$100

This removes excessive copper or lead fouling from the barrel. 

Accessory install — $25 for the first half hour; hourly service rate thereafter

We will install and set up any accessory you have for your firearm. 

Optics mounting with leveling and bore sighting — $25-$50


Bore sighting — $10

Scope ring lapping — $35-$50. Free if scope and rings are purchased here. This trues the front and rear scope rings to each other. When this service is done the scope rings are then married to that firearm and should not be removed from the firearm or used on a different firearm. 

Clear squib round or barrel obstruction — $25 for the first half hour; hourly service rate thereafter

Sighting in, factory ammunition only — $30 (customer provides ammunition)

Barrel dent removal — $25 minimum

Light rust removal — $50 per hour

Pistol Services


Sight alignment or adjustment — $15

Sight removal and installation — $45 minimum (plus parts if needed)

RMR installation (does not include machining slide) — $25-$50

Installation of rear dovetail RMR adapter plate. (Such as the Outer Impact style adapter plate.) $25 minimum, filing and fitting additional at additional service rate.

Aftermarket trigger install — $50 minimum

Polish feed ramp — $25-$35

Switch magazine release side — $20

Polymer pistol grip/module seam line removal — $25-$50

This will remove lines and flatten any ridges left over from the molding process. This is helpful for creasing comfort for those who shoot/train a lot with their pistol. 

Shotgun Services


Trigger lightening — $25-$50 (plus parts)

Barrel Porting — $100-$125

Forcing cone lengthening — $110  ***Coming Soon***

Drill and tap the receiver and install weaver rail. (Not available on all models.) — $100-$150

Stock shortening with recoil/decelerator pad install

Wood — $150 (pad included), $100 (using customer pad)

Composite — $250 (pad included), $200 (using customer pad)

Recoil or decelerator pad install and fitting (no stock cutting) — $50 (plus parts)

Custom length of pull fitting and stock adjustment — $200-300

Full shotgun service (12ga and 20ga only.) — $650-$750 

This service will fit the shotgun to the shooter, as well as help mitigate recoil for the smaller, older or disabled shooter. Customer fitting firearm to shooter will include customer measuring the stock to the shooter as well as fitting a decelerator pad. This does involve customizing synthetic stocks to accept the recoil pad. This will add a small amount of weight at the end of the butt stock which will help with recoil. This service also includes barrel porting and lengthening the forcing cone which both will reduce felt recoil as well. The shooter must be present for initial sizing and measurement. 

Install mid bead on vent rib barrels — $30

Remove stuck choke tubes — $25 for the first half hour; hourly service rate thereafter

Sling swivel installation — $35 (per hole)


Rifle Services

Locking Lug Lapping — $100

Trigger job (polish surfaces, shim if needed and spring) — $55-$85

Stock inletting for low bolt handle — $50 minimum

Free float barrel — $50-$70

Pillar bedding — $125-$200

Action bedding — $150-$225

Stock stiffening — $75

Stock shortening with recoil/decelerator pad install

Wood — $150 (pad included), $100 (using customer pad)

Composite — $250 (pad included), $200 (using customer pad)

Recoil or decelerator pad install and fitting (no stock cutting) — $50 (plus parts)

Custom length of pull fitting and stock adjustment — $200-300

Aftermarket trigger install — $50 and up (plus parts)

Sling swivel install —  $30 (per hole)

Wood work

Complete stock refinishing 

One Piece

Two Piece

Wood dent removal — $20 (per dent)

Crack repair:  Requires inspection and estimate.

Hydrographics

Material cost will vary and is in addition to the price below.

- Full Dip — $250

- Stock & Forearm — $150

- Receiver & Barrel — $150

- Barrel Only $100

- Receiver Only $75

Custom masking (parts left without graphics, paint or in the original finish) by estimate


AR 15/AR 10 services

Call for pricing